Mã lỗi KONICA 1015-1018
Konica 1015
error Code
|
Description
|
F09
|
Power leakage of some kind. Heat, exposure, AC or power supply.
|
F23
|
Toner motor
|
F26
|
Toner density adjustment problem. This means machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel that you should disconnect the toner motor first. This Код ошибки happens probably because either machine wasn't set up properly, or the customer kept on using the machine with the toner light on.
|
F28
|
Corona problem. Could be any corona. Must reset with "25: mode, "P45" set to "0"
|
F34
|
High fuser temperature
|
F35, F36
|
Low fuser temperature
|
F41
|
Scan home
|
F42
|
Scan home
|
F43
|
Exposure lamp
|
F45
|
Lens problem
|
F54
|
Fan motor
|
F60
|
ADF to main board communication problem
|
F67
|
ADF error
|
F77
|
Sorter gate
|
F88
|
AE adjustment problem
|
J11-J13
|
Feed jam
|
J16
|
Jam inside
|
J31, J32
|
Exit jam
|
J61, J62
|
ADF jam
|
J63
|
ADF exit jam
|
J72
|
Sorter jam
|
P20
|
Drum unit or toner level connection problem
|
P25
|
300 copies have been run since toner light came on. Depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
|
P26
|
Must adjust TDS in 47 mode
|
P64
|
ADF & operator are confused
|
P68, P69
|
ADF feed problem
|
P71
|
Sorter interlock
|
P81
|
Key counter not installed
|
Konica 1018
error Code
|
Description
|
F18
|
Paper lift did not complete
|
F23
|
Toner motor
|
F24
|
Pre clean lamp problem
|
F26
|
Toner density sensor
|
F34
|
Fuser overheat
|
F35
|
Fuser temperature too low. Lamp, thermofuse open wire
|
F36
|
Fuser temperature erratic. Probably thermistor
|
F41
|
End of scan sensor not actuated
|
F42
|
End of scan sensor not reached
|
F43
|
CVR (copy lamp voltage regulator)
|
F45
|
Lens or mirror movement problem
|
F52
|
Drive problem
|
F55
|
Zero cross.
|
F56
|
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
|
F60
|
ADF/machine interface problem
|
F67
|
ADF drive problem
|
F70
|
Sorter/machine interface problem
|
F77
|
Sorter bin problem
|
F78
|
Stapler problem
|
F86
|
Waste toner see 56
|
F98
|
Duplex problem
|
J11
|
Upper cassette
|
J12
|
Lower cassette
|
J13, J14
|
Paper feed jam
|
J15
|
Duplex unit jam
|
J16, J17
|
Feed jam
|
J19
|
Paper feed jam
|
J31, J32
|
Exit jam
|
J61
|
ADF opened during run
|
J62, J63
|
ADF jam
|
J65
|
RADF reverse jam
|
J72
|
Sorter jam, or sorter interlock opened
|
J75
|
Stapler jam
|
J92-J94
|
Duplex stack gate sensor or other duplex problem
|
J95
|
Duplex motor or duplex jam
|
P17
|
Right door
|
P19
|
Right door of paper feed unit
|
P20
|
Drum not installed properly or toner level sensor connection problem
|
P33
|
Left door
|
P61
|
RADF reverse cover open
|
P64
|
ADF was selected at the wrong time
|
P71
|
Sorter interlock
|
P74
|
Stapler overloaded, or paper left in stapler bin
|
P76
|
Out of staples
|
P81
|
Key counter not installed
|
P82
|
Memory card problem
|
P96
|
Paper in stacker when duplex selected
|
P97
|
Used bypass in duplex mode
|
P99
|
More than one side than the other in duplex
|
Không có nhận xét nào:
Đăng nhận xét