Lỗi CANON IR 2525

ERROR CODE - E0----------E3

Code	Sub Code	Description
E000	0001	Fixing temperature abnormal rise The temperature detected by the main thermistor does not rise to the specified value during startup control.
E001	0000	Fixing unit temperature rise detection The reading of the main thermistor is 250 deg C or more continuously for 200 msec.
	0001	Fixing unit temperature rise detection The hardware circuit detects overheating of the main or sub thermistor for 200 msec.
	0002	Fixing unit temperature rise detection The reading of the sub thermistor is 295 deg C or more continuously for 200 msec.
E002	0000	Fixing unit temperature insufficient rise 1.The reading of the main thermistor is less than 115 deg C continuously for 400 msec 1.3 sec after it has indicated 100 deg C. 2.The reading of the main thermistor is less than 150 deg C continuously for 400 msec 1.3 sec after it has indicated 140 deg C.
E003	0000	Low fixing temperature detection after standby The reading of the main thermistor is less than 140 deg C continuously for 400 msec or more.
E004	0000	Thermistor disconnection detection error When disconnection is detected with connector (J214) for 30 sec continuously.
E010	0001	Unstable rotation of the Main Motor (M1) Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec.
	0002	Unstable rotation of the Main Motor (M1) During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence.
E014	0001	Unstable rotation of the Fixing Motor (M2) Detection is executed every 100 msec after the start of motor rotation; however, the drive detection signal is absent for 2 sec.
	0002	Unstable rotation of the Fixing Motor (M2) During motor rotation, detection is executed every 100 msec; however, the drive signal is absent 5 times in sequence.
E019	0000	Error in Waste Toner Sensor (S17) Warning when the sensor goes on for 2000 consecutive sheets, and error when the sensor goes on for 100 consecutive sheets.  * Error occurs after the delivery if a paper in passage exists.
E020	0000	The path between the sub hopper and the developing assembly is clogged with toner. The Developing Assembly Toner Sensor (TS1) detects the absence of toner,while the Sub Hopper Toner Sensor (TS2) detects the presence of toner. With the Developing Cylinder Clutch (CL3) turned on, the hopper feedscrew motor (M7) is rotated for 1 sec intermittently 194 times; still, theDeveloping Assembly Toner Sensor (TS1) does not detect the presence of toner.  * Error occurs after the delivery if a paper in passage exists.
E024	0000	The connector (J207) of Developing Assembly Toner Sensor (TS1) is disconnected. The Developing Assembly Toner Sensor (TS1) connection detection signal is absent for 100 msec 10 times in sequence. * Error occurs after the delivery if a paper in passage exists.
	0001	The Developing Assembly Toner Sensor (TS1) is disconnected .<At LOW SPEED>  - The developing assembly toner sensor (TS1) ON counter is checked every 2.5 seconds, and the counter increments 1 count every 25 times when the sensor goes on, and 300 counts are reached. <At HIGH SPEED> - The developing assembly toner sensor (TS1) ON counter is checked every 1.5 seconds, and the counter increments 1 count every 15 times when the sensor goes on, and 300 counts are reached.
E025	0000	The connector (J207) of Sub Hopper Toner Sensor (TS2) is disconnected. The Sub Hopper Toner Sensor (TS2) connection detection signal is absent for 100 msec 10 times in sequence.  * Error occurs after the delivery if a paper in passage exists.
	0001	Failure of the Bottle Motor (M6) The bottle motor (M6) is unlocked when it goes on for 12 consecutive times at 0.1 sec. intervals.  * Error occurs after the delivery if a paper in passage exists.
E110	0001	Failure of the Scanner Motor (M21) The Scanner Motor (M21) speed lock signal does not indicate a locked state a specific period of time after the Scanner Motor (M21) has been started.  * The same condition is detected after the error retry is performed.
	0002	Failure of the Scanner Motor (M21) The speed lock signal indicates a deviation 10 times in sequence at intervals of 100 msec after the signal has indicated a locked state.  * The same condition is detected after the error retry is performed.
	0003	Failure of the Scanner Motor (M21) The scanner motor (M21) speed lock signal does not indicate a locked state for 6.5 sec. after a switchover is made from low to normal speed or for 8 sec. after a switchover is made from normal to low speed.  * The same condition is detected after the error retry is performed.
E196	0000	Error in EEPROM access 20 retries failed after error occurred during communication with EEPROM. * Error occurs after the delivery if a paper in passage exists.
E197	0000	Error in communication of Laser Driver PCB (PCB14) Communication error 1 with image PCB
	0001	Error in communication of Laser Driver PCB (PCB14) Communication error 2 with image PCB
E202	0000	There is an error in the detection of the CIS home position. 1.The attempt to detect the home position fails when the CIS is moved forward.  2.The attempt to detect the home position fails when the CIS is moved back.
E240	0000	Error in controller communication The serial communication error such as parity error or overrun error is constantly detected.
	0001	Error in controller communication The serial communication error such as parity error or overrun error is detected while printing.
E246	0000	Writing to the counter PCB (FRAM) failed
E247	0000	Mismatched checksum between the Flash Rom and the FRAM
E261	0000	Error in Zero Cross Zero Cross failed to be detected for 500ms or more while the relay was ON.  * The same condition is detected after the error retry is performed.
E350	0000	SOFT-ID PCB error
E354	0000	Mismatched serial number for the SOFT-ID PCB
E355	0000	Mismatched serial number between the SOFT-ID, the Flash Rom and the FRAM
	0004	System information error
	0005	System information error